for interior decoration, wall/partition cover, pole/column cover, wood material

使用V型溝槽的可彎曲可捲曲的木質面板來製作T捲門。

2024-09-13

Use grooved flexible and rollable wood panel board (Tambour board) to make a Tambour door:

 

彈性和可捲曲木板(捲簾板)的規格說明

 

可彎曲半圓形槽實木或纖維板木條壁板

木種:實木紅橡木、中密度纖維板

尺寸:4英尺 x 8英尺(1200 mm x 2400 mm)

高度:6毫米

半圓條:18毫米寬

底部:環保樹脂強化不織布底

產地:台灣製造

具有木皮表面的可彎曲V型槽木條牆壁面板

木材種類:橡木、楓木、櫻桃木和中密度纖維板

尺寸:4呎 × 8呎(1200毫米 × 2400毫米)

厚度:3毫米

V槽平板條: 13毫米、43毫米、67毫米以及其他特殊訂製寬度

結構: 頂層 木皮飾面 中層 纖維板 底層 環保樹脂增強不織布背襯或牛皮紙

Usages:  Interior pole wraps and column covering, wood wall paneling, ceiling, furniture surface covers, flooring, wainscoting, Tambour door, V-grooved flexible wood panel board, Tambour board, MDF board, wood veneer, Rollable wood panel board, flexible and rollable wood panel board, DIY

產地:台灣製造

The best Tambour boards, V-grooved Flexible wood panel boards in three layers, top in selected wood veneer, middle MDF board and back with textile support then V-grooved or fluted on the upper two layers for the flexible and rollable character and with wood slats design will be the best selection for this Tambour door material.

由三層構成的可彎曲木質面板,頂層由精選的木皮貼面製成,中層由MDF板製成,背部支撐著紡織材料,旨在提高可彎曲性、可捲曲性和耐用性,一直是製作捲簾門的首選材料。

Flexible and rollable wood panel board (Tambour board) making a Tambour door:

所需材料:

  • V型槽的可彎曲木質面板(捲簾板)
  • 捲簾門軌道系統(滾輪和導軌)
  • 木工膠或黏著劑
  • 測量尺
  • 螺絲刀
  • 砂紙
  • 表面處理(油漆、染色或清漆)

步驟:

  1. Measure and Cut: Measure the height and width of the opening where you want to install the Tambour door. Use a saw to cut the V-grooved flexible wood panel board (Tambour board)  to the required dimensions. Make sure the cut edges are smooth.
  2. Prepare Track System: Install the Tambour door track system according to the manufacturer’s instructions. This will involve attaching the rollers and guides to the top and bottom of the opening.
  3. Apply Adhesive: Apply wood glue or adhesive to the backside of the V-grooved flexible wood panel board (Tambour board). Make sure to spread the adhesive evenly.
  4. Insert into Track: Carefully insert one end of the
  5. V-grooved flexible wood panel board (Tambour board) into the track system at the bottom of the opening. Gently bend the V-grooved flexible wood panel board (Tambour board) and guide it into the track at the top. Slowly slide the V-grooved flexible wood panel board (Tambour board)  into the track, making sure it moves smoothly.
  6. Test and Adjust: Roll the Tambour door up and down a few times to test its movement. Make any necessary adjustments to ensure that the door operates smoothly within the track.
  7. Trim if Needed: If the V-grooved flexible wood panel board (Tambour board) is slightly wider than the opening, you may need to trim the sides using a saw to ensure a perfect fit.
  8. Finishing: Sand the edges and surfaces of the Tambour door to achieve a smooth finish. Apply your chosen finish, such as paint, stain, or varnish, according to the manufacturer’s instructions. Allow the finish to dry completely before proceeding.
  9. Final Installation: Once the finish is dry, carefully slide the Tambour door back into the track system. Ensure that it moves freely and smoothly along the track.
  10. Hardware Installation: Depending on the design, you may need to attach handles or knobs to the Tambour door for easy operation.
  11. Test and Adjust Again: Roll the Tambour door up and down several times to ensure that it operates smoothly. Make any final adjustments as needed.

Congratulations, you’ve successfully created a Tambour door using the V-grooved flexible and rollable wood panel board (Tambour board).

關鍵詞 捲簾門 V-grooved flexible wood panel board, Tambour board, MDF board, wood veneer, Rollable wood panel board, flexible and rollable wood panel board, DIY