2024-09-23

Building a bar front with our flexible half-round wood paneling board instead of half round wooden strips one by one is easier and faster

Specification sheet of flexible half-round wood paneling board

Flexible fluted Half-Round Solid wood or MDF Wood sticks Tambour Paneling Board

Wood kinds:   Solid Red Oak, MDF board

Size:   4 feet X 8 feet (1200 mm x 2400 mm)

Height:   6 mm

Half round stick:  18 mm width

Backing:  ECO resin reinforced non-woven fabric backing

Origin:    Made in Taiwan

Wood Veneer top flexible grooved wood slats tambour paneling board

Wood kinds:   Oak, Maple, Cherry, and MDF board

Size:  4 feet X 8 feet (1200 mm x 2400 mm)

Thickness:  3 mm

Flat slat by V-grooved:  13 mm, 43 mm, 67 mm and other widths for special orders

Structure:  Top Layer Wood veneer Middle Layer MDF board Bottom Layer ECO resin reinforced non-woven fabric backing or kraft paper

Usages:  Interior pole wraps and column covering, wood wall paneling, ceiling, furniture surface covers, flooring, walls, partitions, wainscoting, pole wraps, column wraps, drawer fronts, tambour doors, Flexible Half-Round panel boards, bar front, half round wooden strips, wainscoting, tambour panel, wood wall paneling, Wall Panels,

Origin:   Made in Taiwan

Building a bar front with flexible wood tambour board is as below:

First- you need to measure the size of the bar front to be covered.

Second- according to the measured size you can trimmed with fine tooth saw or cut length-wise with utility knife.

Third- you can glue on the back of the board and paste Half-Round panel on the bar front.

In the past, this product was half-round solid wooden strips one by one hand-made spliced together. It is not only time-consuming but also costly.

The long and thin strips tend twist, shift and slide during/after cut or milled. It may cause a problem of prone to inconsistencies in alignment spacing and parallelism of the strips.

Now, our Flexible Half-Round panel board is in full sheet 4’ (width) x 8’ (height).

The key point is our full sheet Flexible Half-Round wood tambour panel is cheaper than the old product with strips one by one.

It not only can be used on bar fronts but also can be used on curved walls, partitions, wainscoting, pole/column wraps, drawer fronts and tambour doors.

Please refer to our Half-Round panel board Code No. CY300-02 & CY300-01N as below.

If interested in our flexible half-round wood panel tambour board for bar front decoration, please find below the information regarding building a bar front by this wood tambour panel board.

First: Measure the size of the bar front that needs to be covered.

Second: Trim the measured size using a fine tooth saw or cut lengthwise with a utility knife.

Third: Apply glue on the back of the board and affix the Half-Round tambour panel onto the bar front.

Then, you got a half-round wood strips covered bar front.

In the past, the bar front was constructed by hand-making half-round solid wooden strips and joining them together. This process was not only time-consuming but also expensive. The long and thin strips had a tendency to twist, shift, and slide during and after cutting or milling, resulting in inconsistencies in alignment, spacing, and parallelism of the strips.

Now, we offer Flexible Half-Round panel boards in full sheets measuring 4′ (width) x 8′ (height). The key advantage of our full sheet Flexible Half-Round tambour panel is its cost-effectiveness compared to the old method of using individual strips. These flecible wood tambour panels can be used not only for bar fronts but also for curved walls, partitions, wainscoting, pole/column wraps, drawer fronts, and tambour doors or tambour windows. Please refer to our Half-Round panel board Code No. CY300-02 & CY300-01N.

Key words: wood wall paneling, Wall Panels, bar front, wood wall paneling, ceiling, furniture surface covers, flooring, walls, partitions, wainscoting, drawer fronts, tambour doors, tambour panel, Flexible Half-Round panel boards, flexible half-round wood panel board, half round wooden strips